Category Archives for "Uncategorized"

Replacing Old Shower Drain

Shower drains last a long time, but eventually they will need to be replaced. Chelmsford plumbing and heating can take care of the problem for you , or you can try to replace it yourself. You can complete this job yourself with a few materials from your local home improvement store. Replacing your shower drain is rather easy. You will need access to your basements, or crawl spaces in order to complete the work. Follow these steps to replace a shower drain.

Remove Old Drain

The old drain is sometimes challenging to remove. Use the hacksaw blade to cut as much of the drain out as possible. If there are parts that you can’t remove with the blade, use a screwdriver to force them off. Pull the drain completely out and remove the washer as well. You will have to stick your hand in the drain to get the washer out.

Put Components in Place

Place the nut and rubber washer in place. They need to be placed in the sink, down into the shower drain, below the tub line. Next you will add a soft flexible washer or plumber’s putty. Set the top of the drain into place and screw all of the components together. According to plumber Maidstone, it is important that you don’t over tighten as you screw the parts together, because if you do, the threads will not work properly.

Test Fit the Drain

Test the drain to ensure it fits before you seal it into place. Connect the swivel connector to the p-trap of the pipes. Attach the female side of the trap to the drain pipe. Next, connect the swivel nut to the elbow pipe that measures a 90° angle. Once you’ve determined that all of the pieces fit together properly, separate them and set them aside to be sealed. If the new drain seems too short, you can add onto the drain pipe or shorten the base of the swivel connector.

Glue the Drain

Glue all of the pieces together using an all purpose cement. Glue the swivel connector to the p-trap. Next, glue the 90° elbow to the drain pipe. You have to make sure that it is in the proper position. Mark it with a grease pencil during the test fit. Then be sure to glue them together in the same way that you fit them together for the test fit. You want a good seal on these pieces, so apply glue generously. Screw the remaining pieces together and check for leaks. Replacing your old shower drain can be difficult for some people and you can call plumbers in Essex to help you out!.

How It Works: Water Baseboard Heaters

Baseboard hot water heating systems, as their name implies, are typically installed at the baseboard or, at the very least, a point low to the ground. Since heat naturally rises, placing the heating element at the lowest point in a room is an easy way to evenly heat the air in a space.

One unique benefit of using a water based heating system that relies on no form of forced ventilation is that the amount of dust that travels through the air in your home will be lower than in a home where a central air conditioner is blowing air through all the vents.

If the idea of using water to heat the air in a room still seems odd to you, the following information given by Chelmsford plumbing and heating should clue you in on how hydronic baseboard heaters work and how to deal with any problems that could arise.

Components

The hot water in the system is obtained from a boiler in a utility room, and this boiler is heated by gas, oil, or electricity. The hot water is pumped through a system of pipes that are installed in the baseboard. The heat from this hot water is transferred to the room, and once the heat transfer has cooled the water down again, it’s piped back to the boiler room, replaced by a fresh influx of hot water, and reheated.

The hot water pipes on these baseboard heaters are typically made of copper and are uniquely fin-shaped to ensure faster dissipation of heat from the surface of the pipe. According to plumbers Essex, this radiator type structure is similar to the construction of radiators you would find in automobiles.

Function

The quantity of water in a baseboard hot water heating system needs to be kept at a constant volume, and any loss of water has to be compensated from an overhead tank that contains the water storage. The function of the boiler is connected to the thermostats in the room or rooms being heated and when the temperature reading on these thermostats are increased a signal is sent which heats up the boiler and activates the pump to send water to the area demanding the heat needed.

It’s undoubtedly less expensive to plug in either of these single units to heat a small space rather than an entire home, the specific energy savings, heating times, and effectiveness will depend on factors unique to your home. These include the prices for electrical utility use in your area and even how well you’ve sealed leaks, drafts, and other issues in your home that let heat escape. If you want to know more about your water baseboard heaters and how you can use them efficiently in your home, do not hesitate to call plumbers Maidstone to help you out!

 

Signs Your Boiler Needs To Be Replaced

You don’t need to wait until a boiler completely breaks down before replacing the unit. Which can cause hassle like the need for heat on a very cold day. Since the failure is unexpected there are no funds allocated to fix the problem. Now suddenly you have to shell out enormous capital to replace the boiler. Now the first tip in avoiding this problem is to implement a regular check up with a qualified contractor like Chelmsford Plumbing And Heating to handle your maintenance needs. These inspections of the boiler system should occur at least once a year. In order to ensure the owners maintain their full-warranty, be sure to call Chelmsford Plumbing And Heating to ensure the safety of your boiler system.

If you missed your annual inspections here are signs that your boiler needs to be replaced:

Leaks: A boiler that leaks or requires additional make-up water could be nearing the end of its lifecycle. By replacing the existing unit, the building manager or owner can avoid costly floods and critical boiler or property damage. Expert Chelmsford Plumbing And Heating can help you replace your worn out boiler.

Energy Costs: Be mindful of any increases in energy expenses. If energy bills are slowly rising it may be due not only to the age of the boiler but also due to increasing costs of the boiler maintenance. If a boiler requires constant servicing, the system has likely become less efficient. One should consider upgrading to a more reliable, durable unit such as a cast iron unit. Additionally, a noisy unit also may be a sign that it’s time for an upgrade.

Age: Condensing boilers haven’t been on the market for a long time and therefore it is hard to predict their longevity. With proper maintenance, they are expected to last at least 15 years or longer. Essex Plumbing And Heating boilers come with a 10 year non-prorated heat exchanger warranty for commercial boilers, 12 year non-prorated heat exchanger warranty for residential boilers and two year parts warranty for both categories. Cast iron boilers, on the other hand, should be considered for replacement if they have been operating for more than 20 or 30 years. Some of these boilers can last even up to 50 years or longer, but even with decent annual maintenance, their efficiencies are much lower than today’s cast iron boilers. Often times, the energy savings from a new boiler replacement alone practically pays for the cost itself within a year or two.

Comfort: If you notice that some rooms in a building are too hot or too cold or have varying temperatures throughout the day, it’s possible that the unit and its controls are no longer effective or the facility may benefit from more efficient controls.

Increased frequency of failures: This is a clear indicator that the unit is due for either a major overhaul or replacement. Frequent failures of your boiler can give you a conclusion to finally replace it since it cannot do its job anymore efficiently. Chelmsford heating experts can help you with the replacement or overhauling of your boiler which is not performing well anymore.

You can always call your local plumber and heating services to get expert advice on your boiler. You will know whether you can save what you have or get a new one.

Avoid Plumbing Problems With These Preventive Maintenance Tips

Plumbing problems can occur from time to time like broken pipes, clogged drainage, water heater running cold, faucet leaks, what do you do? Do you prefer avoiding this plumbing problems? Understanding this problems and performing preventive maintenance can help you avoid this problems from occurring. Your first step in involving yourself in preventive maintenance is knowing everything that is included in your water system. These are everything that uses water in your home, such as the sinks in your bathroom, kitchen and laundry/utility room, your appliances such as the refrigerator, garbage disposal and washing machine, toilets, showers, and your water heater. All of these can be maintained to prevent plumbing problems from getting out of hand. Plumber Chelmsford are experts in doing plumbing jobs if you need help sorting out your plumbing problem give us a call.

Here are some preventive tips you can use to avoid plumbing problems

Check the hoses for signs of cracks, brittleness, or leaking. Replace your hoses as needed. If you have a septic tank, you should have it regularly inspected. Add pumping your septic tank to your list as an important part of maintenance.

If you have a sewer system, it is good to understand how your lines run and inspect for tree roots that could potentially damage your sewer lines. A preventative measure would be to have your sewer lines snaked periodically to avoid clogging. Chelmsford Plumbing And Heating are experts in handling sewer checks and maintenance to ensure no problems will occur.

Fix leaking faucets and showerheads. Dripping faucets can waste a lot of water and that can add to your bill. And if you don’t fix a dripping faucet or showerhead, the drip can get worse over time. Those problems can cause water damage. To prevent problems, check your facets regularly for leaks and make repairs as needed. Check the handles to make sure no water drips when the handles are turned to the off position and check underneath the sinks for water stains or drips when the water is running.

Fix leaking toilets. Sometimes a faulty seal around the valve seat can cause your toilet to run even when it is not flushed. Over time, gunk will form around the valve seat and flapper. This gunk will prevent the flapper to seal properly, which will cause the water to continue to run. Another problem could be with the handle or tank stopper. The repair that is needed is often quick and inexpensive maintenance. To avoid high maintenance call Chelmsford Plumbing And Heating to address your toilet problems easily.

Unclog slow drains. When the water is slow to drain there may be a problem. Before it gets out of hand, use a homemade mixture of vinegar and hot water to flush down the drain and unclog any debris. This preventative maintenance tip can be done every few months and will get the drain flowing again.

Look inside the burner chamber of your water heater. You shouldn’t see any flakes of rust inside of the chamber. And verify the flame of the water heater is a blue color with no signs of yellow in the flame. If you see a yellow color, this may mean that the jets need to be cleaned.

Follow these simple tips and you can prevent further plumbing problems.

Heating System Safety Tips

A proper home heating in Brentwood is a must in order to survive those chilly nights. It could keep you comfortable when the temperature goes down. But heating systems can also be a hazard due to malfunctioning and can cause fire on homes in Chelmsford. It is advisable to keep your heating systems in its top condition and follow proper maintenance tips. You might also need the help of experts like Chelmsford Plumbing And Heating. They can help you maintain your heating system at home and keep it in top condition. Here are certain easy to follow safety tips keeping, if kept in mind, will help you ensure a secure environment for your family members and maintain home safety without any problem.

  • Follow the Fireplace Safety Tips – Make sure to follow the fireplace safety tips thoroughly at home. Keep a sturdy screen in front of the fireplace so that the sparks don’t flow into the living room. If you are planning to put the fire ashes into a covered metal container, be sure to cool it properly. Don’t put these ashes into a plastic container. Also, keep these ashes at a safe distance from your home. Chelmsford Heating And Plumbing can keep your heating system always safe at all costs.
  • Clean the Chimney – If the heating system at your place has a chimney, make sure it’s thoroughly cleaned at least once a year. If it’s not in regular use, there are high chances that you suddenly discover a small animal, with its nest, residing in your chimney. If you think that it’s not possible for you to check the chimney on your own, consider getting in touch with a heating contractor, who has experience of cleaning chimneys thoroughly. However, be sure to clean the chimney before you use it for the first time this winter.
  • Follow the Safety Tips for Heating Equipment– Consider contacting a qualified heating contractor like Essex Plumbing And Heating for installing the stationary space heating equipment or the central heating equipment. Be sure to follow the manufacturer’s instructions while installing a wood burning stove. Make sure you keep the portable generators away from your house in order to avoid accidents.
  • Change Your Smoke Detector Batteries – A properly maintained smoke detector is a must If there is a smoke detector in your heating system, be sure to change the batteries at frequent intervals, ideally twice a year. If you have not been doing this consistently, do it before turning on the furnace for the first time. You should remember that heating equipment fires often happen to be one of the most common causes of home fires. If you change the batteries of the smoke detector, it will function properly and all your family members will be notified as soon a fire occurs.
  • Have Your Furnace Checked – Make sure you contact a professional heating contractor to get your furnace checked thoroughly, at frequent intervals. Doing this will allow you to have some peace of mind regarding the efficiency of the heating system. If you are based in Chelmsford, there is no reason to worry since you can easily find a reliable and reputed local HVAC contractor Chelmsford Plumbing And Heating. Be sure to explain the exact problems to the professional, if there are any. This will help him solve the problems better and faster.
  • Turn Portable Heaters Off – Before you go to sleep or go out of the house you need to make sure portable heaters are off. It doesn’t really make sense to keep the heater on when you are not indoors. At the same time, you won’t be able to notice if there is a fire hazard when you are sleeping. Make sure you use the home heating systems properly and turn those off when these are not being monitored. This will help you ensure complete security for your home.

DJW Plumbing: Household Leaks 101

Leaking pipes or leaks is one of the most unfortunate things that can happen in your household. You will be wondering for some time on how it is possible for something like that to happen. Leaks can waste water, damage your home, and encourage unwanted organic growth. There are times you cannot see most of the pipework in your home, you may not always know that a leak has formed. One of the best ways to protect your home from future leaks is to understand and look for common situations that cause leaks to develop.

  • Extreme Temperature Changes. Unexpected rapid temperature changes in your pipes can force the pipes to expand and contract. This expansion and contraction may crack the pipes, especially when caused by freezing temperatures. Cracked pipes will be the cause of the leaks.
  • Too Much Water Pressure. We know that high water pressure feels good but uneven or too much of this pressure can harm your pipes. There are pipes and faucets that have limits and can only withstand a specific level of water pressure. The excess pressure will cause the leakage so make sure that the water pressure you have is just enough for your pipes to hold.
  • Tree Roots Intruders. One cause that comes from the outside and not inside your house is tree roots. The tree roots can grow through your water lines causing too much moisture seeping in your yard. If you experience any drop of pressure or notice an uninvited tree growing in your yard, have it checked by a plumbing professional or plumbers Chelmsford.
  • Damaged Pipe Joints. One of the weakest points off the plumbing systems are the pipe joints. As time goes by it can deteriorate and cause leaks. The bad thing about these pipe joints are they are not commonly seen because they are behind walls. So if you hear some banging or any noise made when you turn on your hot water, the pipes must be under too much pressure. If you are in Brentwood, you can call plumbers in Chelmsford to check your pipe joints.
  • Seals Are Broken. When the appliances or your heater was installed there are seals put around the water connectors to prevent leakage. As time goes by, the appliance and the seals age too. If you notice that there are puddles beside the appliance, the seal may have already worn out.
  • Rusting or Corrosion. If you have been using your appliance for so long now, chances are the plumbing system has aged and rust might have eaten your pipes.  If you notice any discoloration in your water, call a plumber Essex right away and have it checked.
  • Your lines are clogged. Another reason for a common household leak is the clogged line, you may wonder how it is connected.  If the lines are clogged, this may cause the pipes to burst and have leaks in your home.
  • You have a loose water connection. This may be caused by appliances that have high vibrations. One good example is your washing machine; the pipe that is attached to it might have loosen because of the frequent vibrations of the appliance.

You need to give attention to your pipes from time to time to prevent any leaks from happening. But if you notice a change on the water flow, an increase in your water bill or just simply a nasty smell inside your house, have it checked right away. You can call your local plumber to prevent any further damages.